DATA HIDROLIK WINDLASS REFERENCE
DZC 5001/5002 Horizontal Anchor Windlass
Review the current Data Hidrolik DZC 5001/5002 horizontal anchor-windlass reference variants and published selection fields. Final chainwheel, drive, controls, brakes, clutches, deck interfaces and documentation are confirmed against the vessel and written quotation.
Data Hidrolik reference range, ERBA Marine project supply
Images and published reference values on this page are attributed to Data Hidrolik and are presented for technical comparison. ERBA Marine is the enquiry and project-supply contact. Availability, final make and model, configuration, compatibility, included accessories, documentation, any required approval or certification, warranty, price, delivery and installation or commissioning scope are governed only by ERBA Marine's written quotation. This page is not an offer and does not imply blanket certification.
PUBLISHED REFERENCE DATA
DZC 5001/5002 drive variants
All current non-disputed catalogue variants and selection fields are shown below. Corrections identified in the research record are applied explicitly; final project values remain quotation-specific.
DZC 5001E / 5002E (AC)
| Selection field | Published reference value |
|---|---|
| Drive Type | AC Electric Motor (210–440V, 3-phase) |
| Continuous Pull | 4,100 kg (30 min) |
| Maximum Pull | 5,500 kg (2 min) |
| Hauling Speed (Single Speed) | 11 m/min |
| Chain Size | 23–26 mm DIN766, 22–24–26 mm Stud-link |
| Approximate Weight | — |
| Current Draw | 21A (11000W) |
| Motor Power | 11000W (400V – 50 Hz) |
DZC 5001H / 5002H (Hydraulic)
| Selection field | Published reference value |
|---|---|
| Drive Type | Hydraulic Motor |
| Continuous Pull | 5,000 kg (30 min) |
| Maximum Pull | 5,500 kg (2 min) |
| Hauling Speed (Single Speed) | 12 m/min |
| Chain Size | 23–26 mm DIN766, 22–24–26 mm Stud-link |
| Approximate Weight | — |
| Hydraulic Pressure/ Flow Rate | 210 bar – 50 L/min |
| Motor Power | — |
Selection note: Approximate weights, pull, speed, electrical and hydraulic values are reference data for the named variant. Confirm chainwheel, options, duty, foundation, controls and required documents before ordering.
TECHNICAL SELECTION
Information to send ERBA Marine
The same data set supports model selection, system coordination and a clear quotation boundary.
- Vessel type, newbuild / retrofit / replacement and operating area
- Vessel name, shipyard or hull number, principal dimensions and equipment number if applicable
- Anchor quantity, type and mass, plus chain length and maximum anchoring depth
- Chain diameter, grade and standard, including DIN 766 or stud-link details
- Required continuous and maximum pull, hauling speed and operating duty
- Horizontal or vertical arrangement, chainwheel quantity, warping head and clutch or brake requirements
- Mooring-rope diameter, construction and minimum breaking load for capstan duties
- Electrical voltage, phase and frequency or hydraulic pressure, flow, return, cooling and filtration
- Deck thickness, foundation, chain lead, chain locker geometry, access and service clearances
- Local, bridge, deck, foot-switch, remote, chain-counter and emergency-stop requirements
- Chain stopper, chain-end fastening and emergency-release requirements
- Flag, class, owner or shipyard documents, inspections and certificates required for the order
- Delivery location, target schedule and installation or commissioning boundary
QUOTATION PROCESS
From vessel data to written scope
Each step narrows the technical boundary and records what is included in the quoted supply.
1. Send vessel and duty data
Share the arrangement, anchor and chain data, pull and speed duty, available power, controls and documentation requirements.
2. Review the complete system
ERBA checks the windlass or capstan together with deck geometry, chain or rope, foundation, drive, controls and support equipment.
3. Confirm the supply configuration
The selected reference, drive variant, chainwheel or drum, accessories and project interfaces are defined for technical and commercial review.
4. Quote the written scope
The quotation states the final make and model, included equipment, documents, warranty path, price, delivery and service boundary.
RELATED REFERENCES
More Horizontal Windlasses
Compare adjacent reference families, then use the enquiry form to confirm the correct technical route.
Compare another current reference family in the same windlass orientation.
Compare another current reference family in the same windlass orientation.
Compare another current reference family in the same windlass orientation.
FREQUENTLY ASKED QUESTIONS
DZC 5001/5002 technical questions
These answers define the reference and quotation boundary; page FAQ markup is owned by the native Elementor accordion.
Confirm the exact drive variant, anchor and chain data, continuous and maximum pull, hauling speed, duty, chainwheel arrangement, deck and locker geometry, power supply, controls and required order documents.
No. They are technical reference pages. Only ERBA Marine’s written quotation confirms the final make and model, configuration, compatibility, included scope, price and delivery.
No. No blanket certification is claimed. State the flag, class, owner and shipyard requirements so evidence for the exact quoted equipment and order can be confirmed.
Yes. Send the existing nameplate, arrangement and foundation drawings, chain or rope data, power and controls, clear photographs and the required new duty.
No. Published values are reference data for named variants. Final performance and duty depend on the drive supply, chain or rope, deck arrangement, controls, system losses and operating conditions.
Send the vessel, anchor and chain or mooring-rope data, required pull, speed and duty, arrangement, available electrical or hydraulic power, controls, support equipment, documents, schedule and delivery location.
TECHNICAL ENQUIRY
Request review for DZC 5001/5002
Send the available vessel, chain or rope, duty, drive, control and documentation data. Missing items can be identified during review.