Home Products Water Makers Marine Water Maker Accessories and Spare Parts
COMPATIBILITY-LED SPARES SUPPORT
Marine Water Maker Accessories and Spare Parts
Source water maker service parts through ERBA Marine with compatibility checked from the installed make, model, serial number, voltage, frequency, photographs and existing part references.
- Selected and supplied through ERBA Marine
- Current configuration and documentation confirmed in writing
- Applicable warranty and after-sales route stated in the quotation
- Eleven functional spare-part groups
- Model and serial verification
- Photo, drawing and part-number review
- Required quantity and destination confirmed
SPARES ORGANISED BY FUNCTION
Identify the component group, then verify compatibility
A website label alone is not enough for safe replacement supply. ERBA Marine checks the installed equipment and mating interfaces before confirming a part.
Membranes and Housings
Membrane reference · vessel duty
Replacement membrane and housing requirements checked against the installed system.
Low-Pressure Pumps
Feed and transfer duty
Pump requirement checked from model, flow, pressure, voltage and connections.
High-Pressure Pumps
Reverse-osmosis pressure duty
Current pump and drive arrangement confirmed from system records and photographs.
Electric Motors
Voltage · phase · frequency
Electrical and mechanical interfaces confirmed before replacement supply.
Controls, Sensors and Electronics
Model and software compatibility
Control panel, sensor and electronic requirements checked from the installed version.
Filters, Cartridges and Housings
Size · rating · connection
Filter and housing details confirmed for the existing pre-treatment arrangement.
Valves
Material · size · function
Valve type and connection details checked against the current system.
Brass Fittings
Thread and connection review
Material, thread, size and mating components confirmed before supply.
Pneumatic Fittings
Tube and port compatibility
Tube size, port thread and operating duty checked from the existing fitting.
Chrome and Stainless-Steel Fittings
Material and interface review
Replacement fitting requirements checked from photographs, dimensions and thread data.
O-Rings and Seals
Dimensions and material
Seal requirement checked from model, part reference, groove data or verified sample details.
Selection note: For a reliable compatibility check, send the water maker make, model, serial number, voltage, frequency, clear component photographs, existing part number, measured dimensions where relevant and required quantity.
Aqua Prime marine water makers supplied through ERBA Marine
ERBA Marine is listed on Aqua Prime’s official dealers and services page in Dubai. ERBA Marine reviews vessel data, compares the current Aqua Prime range and coordinates the confirmed equipment supply and documentation.
The selected configuration, applicable warranty terms and after-sales route are stated in ERBA Marine’s written quotation.
TECHNICAL SELECTION DATA
What ERBA Marine needs before confirming supply
A complete project brief reduces unsuitable selections, missing interfaces and avoidable quotation revisions.
- Water maker make, exact model and serial number
- Vessel voltage, phase and frequency
- Existing part number and any label information
- Clear overall and close-up photographs
- Measured dimensions, threads and connections where relevant
- System location and operating symptoms
- Required quantity and whether matching sets are needed
- Previous service history or available manual reference
- Delivery country, port and required date
- Any current class, flag or documentation requirement
VERIFIED OFFICIAL DOWNLOADS
Manufacturer brochure and selection reference
Use the documents for preliminary review. The selected equipment’s current datasheet and applicable documents are confirmed in the quotation.
Water Maker Selection Guide
Verified complete Aqua Prime selection guide. This download is in Turkish; ERBA Marine can clarify the project-selection points.
Current model-specific technical documentation is confirmed with the selected equipment and written quotation.
FREQUENTLY ASKED QUESTIONS
Marine Water Maker Accessories and Spare Parts FAQs
Practical answers for preliminary selection and quotation planning.
A photograph helps, but the make, model, serial number, voltage, frequency, part reference and measured interfaces may also be required before supply.
No. Similar-looking pumps, motors, filters, valves and fittings can use different electrical or mechanical interfaces. Compatibility is confirmed from verified equipment data.
Include the complete component, label or nameplate, connectors, threads, mounting points and surrounding installation. Add a scale or measured dimensions where useful.
ERBA Marine can review the required quantity and matching components after the exact installed version and service scope are confirmed.
Applicable warranty terms are stated for the quoted part and supply scope. No fixed duration is assumed from a general spare-parts page.
Send a Technical Water Maker Enquiry
Complete the technical fields and attach available drawings or photographs. ERBA Marine will review the duty before confirming the current equipment and supply scope.
Alternative: Send the first details by WhatsApp. Technical confirmation remains subject to the written quotation.